Blog

Zuhause> Blog > So lernen Sie, wie Sie Kunststoffformen reinigen

So lernen Sie, wie Sie Kunststoffformen reinigen

2020-03-23

Jedes Produkt muss über die richtigen Wartungskenntnisse verfügen, und Formprodukte sind keine Ausnahme. Als Schlüsselprozess für die Wartung und Reinigung von Formen hat dies einen sehr wichtigen Einfluss auf die Wartung der Formen. Jiehui Chuang Xiaobian wird einige plastische Kenntnisse der Schimmelpilzreinigung teilen.

clean plastic molds

1. Standardisierte Reinigungsverfahren

Systematic mold maintenance is based on maintenance requirements and continuity of repair operations. In order to achieve the "cost-effective" goal, cleaning the mold must pay attention to: develop a detailed mold cleaning plan. When cleaning different parts of the mold, such as cleaning inside the press, wiping the edges, conventional cleaning, and cleaning of the main parts, the cleaning operation methods used are also different.

After the mold runs for a certain period and after appearance tests such as galvanic wear, track marks, and mold residue content in vented and non-vented areas, technicians can determine the procedure and frequency of mold cleaning through visual inspection. Therefore, it is very important to understand the cycle of safe operation of the mold, and to archive the observation reports of the accumulation of residue and wear inside the mold.

Based on the mold has a certain operating cycle, all molds should be accompanied by relevant maintenance procedures and documentation of the maintenance cycle. In general, controlling internal grease levels and gear broaching, sliders, internal pins and bushings, and other operating conditions of moving parts is the key to stable production. Other factors affecting production include contamination or blockage of waterlines and water jets, leaking manifolds, rust and corrosion due to leaks or condensation.

2. What level of cleaning is enough

Generally, when the molding process operation is completed, dirt or residues are often left on the mold. For different types of residues, the final cleaning requirements are different. Resins such as polyvinyl chloride generate hydrogen chloride gas, which can corrode many types of mold steel. Other residues are separated from flame retardants and antioxidants and can cause corrosion to steel. There are also pigment stains that rust the steel and the rust is difficult to remove. Even ordinary storage water can cause damage to the mold if it is left on the surface of the untreated mold for too long.

Therefore, the necessary cleaning of the mold should be carried out according to the established production cycle. After each time the mold is removed from the press, the mold air holes need to be opened first to remove all oxidized dirt and rust on the non-critical areas of the mold and the template to prevent it from slowly corroding the surface and edges of the steel. In many cases, even after cleaning, some uncoated or rust-prone mold surfaces will soon show rust again. Therefore, even if it takes a long time to brush the unprotected mold, the surface rust cannot be completely avoided.

Many molds now have "self-cleaning" vent lines that have a high gloss. Vent holes are cleaned and polished to the level of SPI # A3, or by milling or grinding, the residue is discharged to the garbage area of ​​the ventilation pipe to prevent the residue from adhering to the surface of the roughing mill stand . However, if the operator manually grinds the mold with a coarse-grained brushing pad, emery cloth, sandpaper, abrasive stone, or brush with nylon bristles, brass or steel, it will cause excessive cleaning of the mold.

Generally, when hard plastics, glass beads, walnut shells and aluminum pellets are used as abrasives for high-pressure crushing and cleaning of mold surfaces, if these abrasives are used too frequently or improperly, this grinding method will also Pores are created on the surface of the mold, and residues are liable to adhere to them, leading to more residue, wear, or premature fracture or burrs of the mold, which is even more difficult to clean the mold.

Therefore, by finding cleaning equipment suitable for the mold processing technology, and referring to the cleaning methods and cleaning cycles recorded in the archives, maintenance time can be saved, and at the same time, mold wear can be effectively reduced.

mail top